Reverb and delay sends
Create a bus track, insert a reverb set to 100% wet, and send each track to it by the amount of reverb you want on that track. Do the same for delay. High-pass the return at 200 to 300 Hz, and start vocal sends around −15 dB.
Why sends
With reverb as an insert on each track, ten tracks need ten reverbs, each a slightly different room, and each track's dry level changes when you adjust its mix knob. With a send, every track that feeds the bus is placed in the same space, the processor runs one reverb, and the return has its own fader, EQ and mute.
Setting up
- Add a bus track and name it for the effect: Plate, Room, Delay.
- Insert the reverb, 100% wet. The dry signal already reaches the master from the track.
- Add an EQ after it. High-pass at 200 to 300 Hz so the reverb doesn't add mud. Low-pass at 6 to 10 kHz if it sounds splashy.
- Send tracks to it. Start with the lead vocal at −15 dB and adjust.
- Set the level in context. Raise the send until you notice the reverb, then back off 2 to 3 dB. In a full mix you should miss it when the bus is muted and not really hear it otherwise.
Starting send levels
| Track | Plate or hall | Room | Delay |
|---|---|---|---|
| Lead vocal | −18 to −12 dB | −20 to −14 dB | |
| Backing vocals | −12 to −8 dB | −18 dB | |
| Snare | −18 to −10 dB | −15 dB | |
| Toms | −18 dB | −15 dB | |
| Acoustic guitar | −20 to −14 dB | −18 dB | |
| Keys, pads | −20 to −14 dB | ||
| Kick, bass | none | none | none |
Low instruments stay dry. Reverb on bass is the fastest way to a muddy mix.
Reverb settings that matter
Decay time. 1.2 to 2 seconds for a vocal plate, 0.4 to 0.8 seconds for a room. A tail that lasts about one bar at slow tempos, and no more than two at fast ones, stays out of the way of the next phrase.
Pre-delay. The gap before the reverb starts. At 0 ms the reverb sits on the consonants and blurs them. At 30 to 60 ms the dry word is heard first and the reverb blooms behind it. A 32nd or 64th note at the song's tempo keeps it rhythmic. The delay time calculator gives the figure.
Size and damping. Larger size reads as further away. More high-frequency damping reads as warmer and less obvious.
Delay
- Slapback: 80 to 120 ms, one repeat. Thickens a vocal or guitar without a tail.
- Rhythmic: 1/4 or 1/8 note, 20 to 35% feedback, with the return low-passed at 3 to 5 kHz so the repeats sit behind the dry signal.
- Ping-pong: repeats alternate left and right for width.
- Delay into reverb: send the delay bus to the reverb as well, so the repeats sit in the same space.
How many
Two reverbs and one delay cover most mixes: a short room that makes close-miked parts sound like they share a space, a longer plate or hall for vocals and snare, and a tempo-synced delay. More than that and the spaces start to contradict each other.
An example
The sample session shown on this site has a bus called Plate carrying a reverb followed by an EQ. The lead vocal sends to it at −14 dB, the keys at −18 dB and the drums at −26 dB.
Quick answers
- Should reverb be on an insert or a send?
- A send, in most cases. One reverb can serve many tracks, the dry signal stays untouched, and you can EQ the reverb separately.
- What should reverb pre-delay be?
- 20 to 80 ms for vocals. Longer pre-delay keeps the reverb from blurring the start of each word.
Audizer does this when you ask.A Mac DAW with an engineer built in. Say what you want and it makes the edit. Free download.
Get Audizer