Where to high-pass each instrument
High-pass every track except kick and bass at a frequency just below its lowest useful note. Vocals at 80 to 120 Hz, guitars at 80 to 120 Hz, snare at 100 Hz, hi-hats and cymbals at 300 Hz or higher. Raise the filter until the part starts to thin in the full mix, then back off.
Starting frequencies
| Source | High-pass at | Lowest fundamental |
|---|---|---|
| Kick | 30 to 40 Hz, or none | 40 to 60 Hz |
| Bass guitar | 30 to 40 Hz | 41 Hz (E1), 31 Hz on a 5-string |
| Low male vocal | 70 to 90 Hz | around 82 Hz (E2) |
| Female vocal | 100 to 140 Hz | around 165 Hz (E3) |
| Backing vocals | 120 to 200 Hz | |
| Acoustic guitar, solo | 70 to 80 Hz | 82 Hz (E2) |
| Acoustic guitar, in a band | 100 to 150 Hz | |
| Electric guitar | 80 to 120 Hz | 82 Hz (E2), lower if detuned |
| Snare | 80 to 120 Hz | 150 to 250 Hz |
| Toms | 50 to 80 Hz | 60 to 150 Hz |
| Hi-hat | 300 to 500 Hz | |
| Overheads, as cymbal mics | 200 to 400 Hz | |
| Overheads, as the main kit sound | 40 to 60 Hz | |
| Piano, in a band | 60 to 100 Hz | 27.5 Hz (A0) |
| Synth pads | 100 to 200 Hz | |
| Reverb and delay returns | 200 to 300 Hz |
Why bother
Every microphone picks up rumble: traffic, footsteps through the stand, air handling, the low thump of plosives. On one track it's inaudible. Across thirty tracks it adds up to a haze under the mix that eats headroom and makes the low end indistinct. The kick and bass sound clearer once nothing else is down there.
How to set one
- Play the track with the mix, not solo.
- Sweep the filter up from 20 Hz until you hear the part lose weight.
- Back off by 10 to 20%.
- Bypass and compare. In the mix, the low end should sound clearer with the filter in and the part should sound the same.
Solo judgment misleads here. A guitar high-passed at 120 Hz sounds thin alone and exactly right with a bass under it.
Slope
| Slope | Use |
|---|---|
| 6 dB/octave | Gentle tilt. Good for thinning a source without an obvious cutoff |
| 12 dB/octave | The default. Natural-sounding |
| 18 to 24 dB/octave | Removing rumble or hum right below the lowest note |
| Steeper | Rarely worth it. Steep filters ring at the cutoff |
Cautions
- Don't filter kick and bass by habit. A high-pass at 30 to 40 Hz removes sub-rumble that most speakers can't play, and that's all. Going higher weakens the foundation.
- Filters shift phase near the cutoff. On multi-mic sources such as a snare top and bottom or a bass DI and amp, filter both the same way or check their sum afterwards.
- A high-pass can raise peak level. The phase shift rearranges the waveform and peaks can come up a decibel or so even though energy was removed.
- Sparse arrangements need the lows. A solo acoustic guitar or piano should keep its full range.
Low-pass too
Bass and kick rarely need anything above 8 to 10 kHz. Distorted guitars have fizz above 8 to 10 kHz that a low-pass removes cleanly. Filtering both ends of supporting parts leaves the top of the mix for vocals and cymbals.
Quick answers
- Should I high-pass everything?
- Everything except the instruments that own the low end, usually kick and bass. Filter only as high as you can without hearing the part get thinner in the mix.
- What slope should a high-pass filter use?
- 12 dB per octave is the general-purpose choice. Use 18 or 24 dB per octave when you need to remove rumble just below a part's lowest note.
Audizer does this when you ask.A Mac DAW with an engineer built in. Say what you want and it makes the edit. Free download.
Get Audizer