Loudness range (LRA): what the number means
Loudness range, LRA, is how far the loudness moves between the quieter and louder parts of a song, measured in loudness units. A song whose verses and choruses are 6 dB apart has an LRA of roughly 6 LU. Most finished pop and rock sits between 5 and 9 LU.
How it's calculated
LRA is defined in EBU Tech 3342.
- Short-term loudness is measured in overlapping 3-second windows across the whole programme.
- Windows below −70 LUFS are discarded, and so are windows more than 20 LU below the overall level. That removes silence and fade-outs.
- The remaining values are sorted. LRA is the distance between the 10th and the 95th percentile.
Using percentiles means a single quiet intro or one enormous hit doesn't define the figure. It describes where the song spends its time.
Typical values
| Material | LRA |
|---|---|
| Heavily compressed pop, EDM | 3 to 5 LU |
| Pop, rock, hip-hop | 5 to 9 LU |
| Indie, singer-songwriter, country | 7 to 11 LU |
| Jazz, acoustic | 9 to 14 LU |
| Film soundtrack, orchestral | 12 to 20 LU or more |
| Unmixed multitrack, faders up | Often 12 to 16 LU |
Reading it
A high LRA on a song means some sections are much quieter than others. Sometimes that's the arrangement, a sparse verse into a big chorus, and it's what you want. Sometimes it's a mix that hasn't been controlled: a vocal that disappears, an intro that needs the volume turned up, a bridge that falls away. Listeners in a car or on earbuds lose anything more than about 10 LU under the loudest part.
A low LRA means every section is about the same loudness. In dance music that's the intent. In a ballad it means the chorus doesn't lift.
LRA and transient punch are separate
A mix can have punchy drums and a small LRA, or flat drums and a large one. Transient punch is crest factor. LRA is about section-to-section movement.
| Low crest factor | High crest factor | |
|---|---|---|
| Low LRA | Loud and flat. Constant density | Steady level with punchy drums. Typical good pop master |
| High LRA | Squashed, with big level jumps between sections | Fully dynamic. Classical, jazz, raw mixes |
Changing it
LRA comes from balance decisions more than from the master bus.
- Level the vocal phrase by phrase so verses don't sink.
- Ride sections. If the verse is 9 dB under the chorus, raise the verse 2 to 3 dB at the track or bus level.
- Compress buses by 2 to 4 dB to bring up quiet playing.
- A limiter reduces LRA a little, by holding the loudest sections down while quieter ones pass.
To widen it, do the opposite: pull the verse down a decibel, mute a layer or two before the chorus, and ease off the bus compression.
A worked example
In our own test mix of a 15-track rock multitrack, the raw faders-up balance had a loudness range of 14.4 LU and was clipping at unity. After the mix, which included levelling the lead vocal's phrases from a 10.8 dB spread to 4.3 dB, it measured 5.8 LU.
Quick answers
- What is a good loudness range for a song?
- 5 to 9 LU for most pop, rock and hip-hop. Acoustic and orchestral music runs 9 to 20 LU. Under 4 LU usually means every section is the same loudness.
- How is LRA different from crest factor?
- Crest factor looks at peaks versus average over milliseconds. Loudness range looks at how the 3-second loudness changes across the whole song.
Audizer does this when you ask.A Mac DAW with an engineer built in. Say what you want and it makes the edit. Free download.
Get Audizer