Multiband compression explained
Use multiband compression when a problem happens in one frequency range only some of the time: a bass that booms on certain notes, a vocal that turns harsh when it gets loud. Set a band around the problem, compress it 2 to 4 dB at about 3:1, and leave the other bands alone.
What it's for
An EQ cut is permanent. Take 3 dB out at 250 Hz and it's gone on every note, including the ones that were fine. A normal compressor reacts to the whole signal, so a loud bass note pulls the cymbals down with it.
A multiband compressor splits the audio with crossover filters, compresses each band with its own threshold and ratio, and adds them back together. Each band reacts only to its own content.
Typical three-band layout
| Band | Range | Contains |
|---|---|---|
| Low | Up to 120 to 200 Hz | Kick and bass fundamentals |
| Mid | 200 Hz to 2 to 5 kHz | Body of vocals, guitars, snare |
| High | Above 2 to 5 kHz | Presence, sibilance, cymbals |
Jobs it does well
| Problem | Band | Settings |
|---|---|---|
| Bass guitar with uneven low notes | Below 150 Hz | 4:1, 30 ms attack, 150 ms release, 3 to 6 dB |
| Vocal harsh on loud notes only | 2.5 to 5 kHz | 3:1, 5 ms attack, 60 ms release, 2 to 4 dB on peaks |
| Acoustic guitar that booms on some chords | 100 to 250 Hz | 3:1, 15 ms attack, 120 ms release, 2 to 4 dB |
| Low end of a mix that jumps around | Below 120 Hz | 2:1, 30 ms attack, 200 ms release, 1 to 3 dB |
| Cymbals too loud in a stereo drum recording | Above 6 kHz | 3:1, 1 ms attack, 80 ms release, 2 to 4 dB |
How to set it
- Bypass all bands except the one with the problem.
- Solo that band if you can and move the crossover until it holds the problem and little else.
- Set ratio to 3:1 and lower the threshold until the meter moves only when the problem occurs.
- Use attack and release as you would on a normal compressor for that source.
- Leave makeup gain at zero. The idea is to remove the excess.
- Bypass the whole plugin and compare. The tone at normal moments should be the same.
What goes wrong
Compressing every band. 4 dB of reduction on all three bands with makeup gain on each rebalances the entire tone on every beat. Mixes done this way sound loud, flat and tiring.
Crossovers through the middle of an instrument. A crossover at 300 Hz cuts a male vocal in two. The halves get different gain changes and the voice changes tone as it gets louder.
Using it for a static problem. If the mud is there all the time, EQ it. Multiband is for problems that come and go.
A de-esser is a multiband compressor
A split-band de-esser is the same idea with one band, centred on sibilance, and a fast attack. If you have a vocal problem in one band, a de-esser tuned lower, around 3 kHz, can stand in for a multiband compressor.
Quick answers
- Where should multiband crossovers be set?
- For three bands, around 120 to 200 Hz and 2 to 5 kHz. Place them between instruments' ranges rather than through the middle of one.
- Do I need multiband compression on the master?
- Usually not. If one band misbehaves in a mix, fixing the track responsible is cleaner. Use it on a master when you can't go back to the mix.
Audizer does this when you ask.A Mac DAW with an engineer built in. Say what you want and it makes the edit. Free download.
Get Audizer