Compressor settings explained
Threshold sets the level where compression starts. Ratio sets how hard it pushes back above that. Attack is how quickly it clamps down, release is how quickly it lets go, knee smooths the transition, and makeup gain restores the level you took off. Set ratio first, then threshold for the amount of reduction, then attack and release by ear.
Each control
Threshold. Signals below it pass unchanged. Lower it and more of the performance gets compressed.
Ratio. 2:1 is gentle, 4:1 is firm, 8:1 is heavy, 20:1 and above is limiting.
| Input over threshold | Output at 2:1 | at 4:1 | at 8:1 |
|---|---|---|---|
| 4 dB | 2 dB | 1 dB | 0.5 dB |
| 8 dB | 4 dB | 2 dB | 1 dB |
| 12 dB | 6 dB | 3 dB | 1.5 dB |
Attack. With a fast attack, 0.1 to 5 ms, the compressor catches the transient and the sound gets smoother and further back. With a slow attack, 20 to 50 ms, the transient passes and only the body is reduced, which adds punch.
Release. Fast release, 30 to 80 ms, recovers between notes and makes things louder and more excited. Slow release, 200 ms and up, holds the gain down and sounds smoother. Too fast on low notes causes distortion, because the gain starts following individual cycles of the wave.
Knee. A hard knee starts compressing abruptly at the threshold. A soft knee phases in over several dB either side and is less audible.
Makeup gain. Compression makes things quieter. Makeup brings the level back so the result is the same loudness as before, with less range.
An order for setting it
- Ratio to 4:1, attack 10 ms, release 100 ms.
- Lower the threshold until you see the gain reduction you're after: 2 to 4 dB for gentle control, 6 to 10 dB for obvious squeeze.
- Sweep the attack. Listen to the front of each note. Stop where it has the right amount of bite.
- Sweep the release. Watch the meter: it should return close to zero before the next note or beat.
- Adjust ratio up or down if it's too obvious or not doing enough.
- Set makeup gain so bypass sounds equally loud.
- Compare. If you can't hear an improvement at matched level, take it off.
Starting points
| Source | Ratio | Attack | Release | Reduction |
|---|---|---|---|---|
| Lead vocal | 3:1 to 4:1 | 5 to 15 ms | 40 to 100 ms | 3 to 6 dB |
| Bass | 4:1 | 20 to 40 ms | 100 to 200 ms | 4 to 8 dB |
| Kick | 4:1 | 20 to 30 ms | 50 to 100 ms | 3 to 6 dB |
| Snare | 4:1 | 5 to 20 ms | 80 to 150 ms | 3 to 6 dB |
| Acoustic guitar | 3:1 | 10 to 25 ms | 100 ms | 2 to 4 dB |
| Piano | 2:1 to 3:1 | 20 to 40 ms | 150 ms | 2 to 3 dB |
| Mix bus | 1.5:1 to 2:1 | 30 ms | 100 to 300 ms | 1 to 2 dB |
What compression can't do
It can't fix a part whose level varies by section. A verse 10 dB under the chorus needs clip gain. It also raises everything quiet: room sound, breaths, hiss, bleed. Clean the track first.
Quick answers
- What does a 4:1 ratio mean?
- For every 4 dB the input rises above the threshold, the output rises 1 dB. A peak 8 dB over the threshold comes out 2 dB over.
- How do I set attack and release?
- Attack decides how much of the transient passes before the gain drops; release decides how soon the gain comes back. Start at 10 ms and 100 ms and adjust by ear.
Audizer does this when you ask.A Mac DAW with an engineer built in. Say what you want and it makes the edit. Free download.
Get Audizer