Drum compression settings
For punch, use a slow attack of 20 to 30 ms so the hit gets through, with a release that recovers before the next hit. For control, use a fast attack of 1 to 5 ms. Kick and snare take 4:1 with 3 to 6 dB of reduction; the drum bus takes 2:1 to 4:1 with 2 to 4 dB.
Settings by drum
| Source | Ratio | Attack | Release | Reduction | Aim |
|---|---|---|---|---|---|
| Kick | 4:1 | 20 to 30 ms | 50 to 100 ms | 3 to 6 dB | Even hits with the click intact |
| Snare, punchy | 4:1 | 15 to 30 ms | 80 to 120 ms | 3 to 6 dB | More crack |
| Snare, fat | 4:1 to 6:1 | 2 to 8 ms | 100 to 150 ms | 4 to 8 dB | More body and ring |
| Toms | 4:1 | 10 to 20 ms | 150 to 250 ms | 3 to 6 dB | Sustain |
| Overheads | 2:1 to 3:1 | 20 to 40 ms | 100 to 200 ms | 1 to 3 dB | Hold cymbals steady |
| Room mics | 6:1 to 10:1 | 1 to 10 ms | 50 to 100 ms | 8 to 15 dB | Size and excitement |
| Drum bus | 2:1 to 4:1 | 30 ms | 100 ms or auto | 2 to 4 dB | Glue |
Attack decides the character
A drum hit is a spike lasting a few milliseconds followed by a body lasting a few hundred. The compressor's attack time decides which part it grabs.
Slow attack, 20 to 30 ms. The spike is over before the compressor reacts. The body is turned down, the makeup gain turns everything back up, and the spike ends up louder relative to the body. That's punch.
Fast attack, 1 to 5 ms. The spike itself is reduced. The drum sounds rounder, fatter and further away, and the ring and room come up.
Release sets the groove
Set release so the gain reduction meter returns to near zero just before the next hit. At 120 BPM, quarter notes are 500 ms apart and eighths 250 ms, so a release of 100 to 200 ms works. If the meter never recovers, the compressor is acting as a volume cut. If it recovers instantly, the tail of each hit swells up, which is exciting on room mics and messy on a kick.
The drum bus
Bus compression reacts to the whole kit, so the kick and snare make the cymbals duck a little and the kit breathes together. 2 to 4 dB is enough. A slow attack keeps the transients. If the cymbals pump audibly on every kick, raise the threshold or lower the ratio.
Parallel instead of more
When you want a kit that sounds heavily compressed but still hits hard, send it to a second bus, crush that with 10 dB or more of fast compression, and blend it under the uncompressed kit. Details in parallel compression.
Before compressing drums
- Gate or edit bleed out of the toms. Compression raises it.
- Check phase between kick in and out mics, and snare top and bottom.
- Fix wildly uneven hits with clip gain. A compressor set for normal hits will flatten the occasional huge one.
Quick answers
- What attack time makes drums punchy?
- 20 to 30 ms. That lets the initial crack through before the compressor turns the level down, which exaggerates the hit.
- How much compression on the drum bus?
- 2 to 4 dB of gain reduction at 2:1 to 4:1 with a 30 ms attack. Enough to make the kit move together.
Audizer does this when you ask.A Mac DAW with an engineer built in. Say what you want and it makes the edit. Free download.
Get Audizer