Bass compression: settings for an even low end
Start with a 4:1 ratio, 30 ms attack and 150 ms release, and lower the threshold until you see 4 to 8 dB of reduction on most notes. Level the take with clip gain first if some notes are much louder than others.
Why bass is different
On a bass guitar, an open E can be 6 to 10 dB louder than the same pitch fretted on the A string. Dead spots on the neck drop single notes. Fingerstyle players dig in on some beats and not others. In the low end those differences are heard as the whole mix swelling and shrinking, because bass carries most of a mix's energy.
A steady bass also lets you set the kick against it once and have it hold for the song.
Settings by style
| Style | Ratio | Attack | Release | Reduction |
|---|---|---|---|---|
| Pop, rock, fingerstyle | 4:1 | 20 to 40 ms | 100 to 200 ms | 4 to 8 dB |
| Picked rock or punk | 4:1 to 6:1 | 10 to 20 ms | 80 to 120 ms | 5 to 8 dB |
| Slap | 6:1 to 8:1 | 5 to 10 ms | 80 to 100 ms | 6 to 10 dB on pops |
| Jazz, acoustic | 2:1 to 3:1 | 30 to 50 ms | 200 ms | 2 to 4 dB |
| Synth bass | 2:1 to 4:1 | 10 to 30 ms | 100 ms | 2 to 4 dB, if any |
Release matters most down low
A low E at 41 Hz takes 24 ms to complete one cycle. If the release is shorter than a couple of cycles, the compressor's gain starts moving up and down within each wave, and you hear that as a fuzzy distortion. Keep release at 80 ms or longer on bass. If the bass sounds gritty under compression, lengthen the release before anything else.
A two-stage approach
- Clip gain. Fix the 2 or 3 notes that are far louder or quieter than the rest.
- First compressor: 4:1, 30 ms attack, 150 ms release, 4 to 6 dB. This evens the notes.
- Second, optional: a fast peak limiter or 8:1 compressor with 1 ms attack, catching only the 2 to 3 dB of pluck that still jumps out.
Low and high bass behave differently
The fundamental, 40 to 120 Hz, wants to be rock steady. The upper harmonics, 700 Hz to 2.5 kHz, carry the pluck and want to move. A single compressor reacts to the loud lows and pulls the highs down with them. Two ways round it:
- A multiband compressor with a crossover near 120 to 150 Hz, compressing the low band at 4:1 and barely touching the rest.
- Splitting the bass onto a clean DI track and an amp track, and compressing the DI harder. See mixing bass DI with an amp sim.
Checking it
Watch the gain reduction meter. It should move on every note and return most of the way between notes. Then listen on small speakers. Every note of the line should be audible at the same level. If some notes vanish there, they lack upper harmonics, and a touch of saturation helps more than extra compression.
Quick answers
- Why does bass need so much compression?
- Low notes vary a lot in level from string to string and fret to fret, and small speakers reproduce only part of the range. Compression keeps every note at a similar weight.
- Should bass compression attack be fast or slow?
- Medium to slow, 20 to 40 ms, so the pluck comes through. A fast attack flattens the note's front and the bass loses definition.
Audizer does this when you ask.A Mac DAW with an engineer built in. Say what you want and it makes the edit. Free download.
Get Audizer