Mix bus chain order
On the master: corrective EQ first, then a compressor taking off 1 to 2 dB, then optional saturation and a broad tone EQ, then any stereo adjustment, and the limiter last with its ceiling at −1 dBTP. Use as few of those as the mix needs.
The chain
| Order | Processor | Typical setting | Skip it when |
|---|---|---|---|
| 1 | Corrective EQ | High-pass at 20 to 30 Hz; narrow cuts of 1 to 2 dB | The mix has no specific problem |
| 2 | Compressor | 1.5:1 to 2:1, 30 ms attack, auto or 100 to 300 ms release, 1 to 2 dB | The mix already holds together |
| 3 | Saturation | Barely on | Nearly always optional |
| 4 | Tone EQ | Broad shelves, ±0.5 to 1.5 dB | The tone matches your references |
| 5 | Stereo control | Mono the lows; small width changes | Width and mono compatibility are fine |
| 6 | Limiter | Ceiling −1 dBTP, 2 to 4 dB of reduction | Never. It's the safety net |
Why this order
Corrective EQ before the compressor. A build-up at 200 Hz or sub-rumble at 25 Hz will trigger the compressor. Remove it first and the compressor reacts to the music.
Compressor before tone EQ. If you brighten the mix and then compress, the compressor pushes back against some of that brightness. Shape the tone after dynamics are settled and it stays where you put it.
Stereo changes before the limiter. Widening raises the side signal and can raise peaks. The limiter needs to see the final signal.
Limiter last. Its ceiling is a promise about the file's peak level. Any gain, EQ or saturation after it breaks that promise.
Settings, stage by stage
Bus compression. Slow attack so drum transients pass. Release timed so the needle recovers in time with the song, or on auto. If you see more than 3 dB of reduction, the threshold is too low or the mix has a level problem that belongs back on the tracks.
Tone EQ. Compare against a commercial track at matched loudness. Typical moves: +1 dB shelf above 10 kHz, −1 dB around 300 Hz, +0.5 dB at 60 Hz. If you want more than 2 dB of anything, go back to the mix.
Limiter. Raise input gain until the loudest sections show 2 to 4 dB of reduction. More in how to use a limiter.
What doesn't belong
- Heavy multiband compression. It's a repair tool for mixes you can't reopen.
- Reverb. Add it to tracks.
- Large EQ moves. A 4 dB master EQ change means a mix problem.
- A limiter pushed 8 dB to match a reference. The reference was mixed to be that dense. Limiting alone won't get you there cleanly.
Mix into it or add it at the end
Processing added at the end changes a balance you'd already approved. Many engineers put the bus compressor and a gentle limiter on once the rough balance is done, and mix through them. Either way works. What doesn't work is adding a compressor in the last ten minutes and not rechecking the vocal level.
Leave it off for mastering
If someone else is mastering the track, send it without the limiter and with peaks around −6 to −3 dBFS. Keep the bus compressor if it's part of the sound. See how loud before mastering.
Quick answers
- What should be last on the master bus?
- The limiter. Anything after it can raise peaks above the ceiling you set. Meters go after the limiter since they don't change the audio.
- Should I mix into a compressor?
- It's a common approach. If you do, put it on early with 1 to 2 dB of reduction and leave it, because it changes how you set every balance.
Audizer does this when you ask.A Mac DAW with an engineer built in. Say what you want and it makes the edit. Free download.
Get Audizer