Audizer
Loudness and mastering

How to master a song at home

Mastering a single song at home comes down to five things: confirm the mix has no problems, compare it against a reference at the same loudness, correct tone with EQ moves of 2 dB or less, set loudness with a limiter under a −1 dBTP ceiling, and measure the result.

Before you start

Take a break from the song, a day if you can. Mastering is a fresh-ears job. Start from a bounced stereo mix that peaks around −6 to −3 dBFS with no limiter on it.

The steps

  1. Measure the mix. Note integrated LUFS, true peak, crest factor and loudness range. Check for clipped samples. Typical premaster: −20 LUFS, −4 dBFS peak, 16 dB crest factor.
  2. Load a reference. A commercial song in the same style whose sound you like. Turn it down until it's the same loudness as your unmastered mix, usually 6 to 10 dB. This step matters more than any plugin. An unmatched reference just sounds louder, and louder sounds better.
  3. Compare tone. Switch between them every few seconds. Is yours darker? Thicker in the low mids? Lighter in the sub? Write down what you hear.
  4. EQ in small moves. A high-pass at 20 to 30 Hz. Then broad adjustments of 0.5 to 2 dB to close the gap you noted. If you want 4 dB anywhere, go back to the mix.
  5. Compress only if it helps. 1.5:1 to 2:1, 30 ms attack, 1 to 2 dB of reduction, to make the mix hold together. Skip it if the mix already does.
  6. Limit. Ceiling at −1 dBTP, true-peak mode on. Raise the gain until the loudest section shows 2 to 4 dB of reduction. See how to use a limiter.
  7. Measure again. Integrated LUFS over the whole song, true peak, crest factor, loudness range. Compare with step 1.
  8. Compare with the reference at matched loudness again. Now raise the reference to match your master.
  9. Check translation. Phone speaker, earbuds, car, mono. The vocal and snare should survive on all of them.
  10. Export as 24-bit WAV at the session sample rate.

What the numbers should look like

MeasurePremasterAfter mastering
Integrated loudness−24 to −16 LUFS−14 to −9 LUFS
True peak−6 to −3 dBFS−1 dBTP or lower
Crest factor14 to 18 dB9 to 14 dB
Loudness range6 to 12 LU5 to 9 LU
Clipped samples00

Where home masters go wrong

Too loud. Chasing −7 LUFS with a limiter alone. Streaming services will turn it down anyway. See LUFS targets.

Too much low end. Small rooms and small speakers hide bass. Check the sub against your reference on headphones.

Too many processors. Each one should fix something you can name. Three is plenty: EQ, maybe a compressor, a limiter.

Fixing mix problems. If the vocal is too quiet, no mastering move raises it without raising the snare. Reopen the mix.

No level matching. Every comparison made at different loudness is biased toward the louder one.

An album or EP

Master the songs in one session and match them to each other by ear, with the lead vocal as the anchor. Quiet songs should be quieter. Don't force every track to the same LUFS: a ballad at the same reading as the rocker will sound too loud next to it.

Quick answers

Can I master my own music?
Yes, for releases where hiring a mastering engineer isn't practical. The biggest gains come from measuring, comparing against references at matched level, and making small moves.
What is the difference between mixing and mastering?
Mixing balances the individual tracks of a song. Mastering works on the finished stereo mix: final tone, loudness, peaks and file format.

Audizer does this when you ask.A Mac DAW with an engineer built in. Say what you want and it makes the edit. Free download.

Get Audizer

Updated 2026-11-15. Corrections: support@intuzu.com