Audizer
Loudness and mastering

How to use a limiter for mastering

Put the limiter last on the master. Set the ceiling to −1 dBTP. Raise the input gain while the loudest part of the song plays until you see 2 to 4 dB of gain reduction on peaks. Measure the integrated loudness of the whole song. If you need more level than that gives, fix it in the mix.

What a limiter does

A limiter is a compressor with a very high ratio and a very fast attack. Nothing gets above its ceiling. You push the mix up into it, the peaks are held down, and the average level rises.

Look-ahead lets it see peaks a few milliseconds before they arrive, so it can turn down smoothly ahead of time. Without look-ahead it would have to react instantly, which clips the transient. The cost is a few milliseconds of delay.

The controls

ControlWhat it doesSetting
Ceiling, or outputThe highest level allowed out−1.0 dBTP
Gain, input or thresholdHow hard you push inUntil 2 to 4 dB of reduction
ReleaseHow fast gain returns after a peak50 to 200 ms, or auto
Look-aheadHow early it starts turning down1 to 5 ms. Often fixed
True peakCatches inter-sample peaksOn

The steps

  1. Check the mix first. Peaks around −6 to −3 dBFS, no clipping, nothing else on the master doing heavy limiting.
  2. Loop the loudest section.
  3. Set the ceiling to −1 dBTP and switch true-peak mode on.
  4. Raise the gain until the reduction meter flicks to 2 to 4 dB on kick and snare hits.
  5. Listen to the kick and snare. Bypass and compare at matched level. If they've lost their front edge, back the gain off 1 dB.
  6. Set release. Faster sounds louder and can distort on bass notes. Slower sounds cleaner and can pump. 100 ms or auto is a safe start.
  7. Play the whole song and read the integrated LUFS.
  8. Measure the true peak of the result and confirm it's at or under the ceiling.

When it won't get loud enough

If 4 dB of limiting gets you to −15 LUFS and you wanted −11, pushing another 4 dB into the limiter will get the number and wreck the drums. The mix has too much peak for its average. Go back and:

  • Compress or clip the kick and snare by 2 to 3 dB. A few stray drum peaks are often what the limiter is spending its effort on.
  • Control the low end. Sub energy uses headroom and adds little loudness. High-pass the mix at 25 to 30 Hz.
  • Add 1 to 2 dB of bus compression before the limiter.
  • Check the vocal. One shouted word can set the limiter's work for the whole song.

Crest factor shows you this. A mix with 18 dB between peak and average needs a lot of limiting. One with 12 to 14 dB is nearly there. See crest factor explained.

Signs you've gone too far

  • The chorus doesn't sound bigger than the verse.
  • The kick ducks the whole mix each time it hits.
  • Held bass notes or vocals have a fuzzy edge.
  • Cymbals swell between snare hits.
  • It's tiring after one minute.

Lower the gain by 2 dB and compare at matched loudness. The quieter one almost always sounds better.

Quick answers

How much gain reduction should a mastering limiter do?
2 to 4 dB on the loudest peaks is clean on most material. Past 6 dB the kick and snare lose impact and sustained notes start to distort.
What should the limiter ceiling be?
−1 dBTP for streaming releases.

Audizer does this when you ask.A Mac DAW with an engineer built in. Say what you want and it makes the edit. Free download.

Get Audizer

Updated 2026-11-15. Corrections: support@intuzu.com